In the electronic circuit overhaul, it is often necessary to remove the integrated circuit from the PCB printed circuit board. Since the integrated circuit pins are dense and dense, it is difficult to disassemble, and sometimes the integrated circuit and the circuit board are damaged. Here are a few examples of effective integrated circuit disassembly methods for your reference.
â— The suction tin is removed by the tin . The use of a soldering tin to disassemble the integrated block is a commonly used professional method. The tool is a common suction and soldering soldering iron with a power of more than 35W. When disassembling the integrated block, just put the heated dual-purpose soldering iron tip on the pin of the integrated block to be disassembled, and after the solder is melted, the tin is sucked into the fine tin, and the solder of all the pins is sucked and the integrated block is Can be taken off.
â— Medical hollow needle removal method. Take a few medical needles 8 to 12 hollow needles. It is advisable to use the inner tip of the needle just to fit the manifold block pin. When disassembling, use a soldering iron to melt the solder on the lead. Use a needle to cover the pin in time, then remove the soldering iron and rotate the needle. After the solder solidifies, pull out the needle. This pin is completely separated from the printed board. Once all the pins have been done this way, the integrated block can be easily removed.
â—Electric iron brush with disassembly method. This method is simple and easy, as long as there is a soldering iron and a small brush. When disassembling the integrated block, first heat the soldering iron. After the soldering temperature is reached, the solder on the lead is melted, and the melted brush is swept away by the brush. This allows the pins of the manifold to be separated from the printed board. The method can be performed separately or in separate steps. Finally, use a sharp tweezers or a small "one" screwdriver to pry the integrated block.
◠Increase the solder melting and disassembly method. This method is a trouble-free method. Just add some solder to the pins of the integrated block to be disassembled (information source: http://) to connect the solder joints of each column of pins, so as to facilitate heat transfer. Easy to disassemble. When disassembling, use a soldering iron to heat a column of pins with a sharp tweezers or a small “one†screwdriver. The two columns of pins are rotated and heated until they are removed. In general, each column of pins can be removed by heating twice.
◠Multi-strand copper wire suction removal method. It is to use a multi-strand copper core plastic wire to remove the plastic outer skin and use a multi-strand copper wire (a short wire head can be used). Before use, apply multiple strands of copper wire to the rosin alcohol solution. After the soldering iron is heated, place the strands of copper wire on the pins of the manifold to heat the pins. The solder on the pins will be absorbed by the copper wires. The upper solder can be cut off and the solder on the pins can be removed by repeating it several times. Braided wires in the shielded wire can also be used if available. Simply suck the solder and use a tweezers or a small “one†screwdriver to gently remove it. The integrated block can be removed.
â—Plus tin removal method. Add solder to the pins of the integrated circuit block, and the solder wire should be of a good kind. After heating with a soldering iron, remove it directly with a sharp cone. This method is generally used by the electronics factory for repair. This method takes the fastest block.
We make 7.4v 2000mah to 20Ah Li Ion Battery Pack for heated clothing all types, including heated glove, heated jacket, heated coat, heated vest, heated shirt, electric heated jacket, heated pants, heated boots, heated gloves, heated underwear, heated jacket liners, heated glove liners, heated work glove, heating vest, heating clothing, heated motorcycle jacket, heated hunting jacket.
most popular model is 7.4v 2 cells battery, typical capacity 2200-2400mah, 2500-2600mah, 2900-3000mah, 3200-3400mah.
7V Heated Glove Battery,Heated Gloves Battery,Hand Warmers Battery,Warmest Gloves Battery
Asarke Industry Co., Limited , https://www.asarke-industry.com